Skip to content

Opportunity overview

Active Federal PPRA / EPADS Official source

CONSTRUCTION OF BOUNDARY WALL AT NBP BANNU CANTT BRANCH (0552) BANNU REGION (TICKET NO. 139388)

Regional Office (National Bank of Pakistan (NBP))

Reference: P194100

Closes today

Tender information

Published
Submission deadline
Category
Civil construction
Procurement method
Request for Quotation
Procuring agency
Regional Office (National Bank of Pakistan (NBP))

Tender description

  • CONSTRUCTION OF BOUNDARY WALL AT NBP BANNU CANTT BRANCH (0552) BANNU REGION (TICKET NO. 139388)

Technical Specifications

CONSTRUCTION OF BOUNDARY WALL AT NBP BANNU CANTT BRANCH (0552) BANNU REGION (TICKET NO. 139388)

Specification
Excavation in all types of soil and up to any depth including removal of excavated material from site at desired location, job complete in all respects. Cft
Specification
Providing / filling earth from out side and leveling the plot and compact sweet earth with viberator and watering, each layer having 6" thickness. Complete in all respect as per entire satisfcation. P.Cft
Specification
Providing and laying under floor cement concrete of the nominal mixes by volume as indicated, using 1-1/2'' down guage stone ballast as coarse aggregate, including formwork and its removal, compacting, curing etc, complete in all respects as per drawing, specifications and as directed by the Consultant / Engineer. Cft
Specification
REINFORCEMENT CEMENT CONCRETE 3000 PSI
Specification
Provide, mix, place and vibrate reinforcement cement concrete in the volumetrix mix. 1:2:4 using one part of op cement to 2- part of 50 % lawrancepur and 50 % chenab sand and 4-parts of sargodha crush nominal size 3/4'' and down mesh with min. cube crushing strength of 3000 psi at 28 days finishing the necked surface and curing etc, including water tight finishing the necked surfaces and curing etc, from work including its sub-sequent removal, complete in all respects as per drawings, specifications and as directed by the Consultant/Engineer.
Specification
II) Beam / Lintels/ Shelves etc. Cft
Specification
STEEL REINFORCEMENT
Specification
P/F Grade 60 steel reinforcement deformed bars at any floor with minimum yield strength of 60000 psi as per ASTM standards A-615, including cost of binding wire of 16-SWG, chairs. (Wastage of bars, Over laps etc. is to be Contractors accounts). kgs
Specification
BRICK MASONARY
Specification
Providing and laying brick masonary/ Solid Block with 1:4 cement sand mortar in super structure, incluing raking out joints, scaffolding, curing, drilling for walls/ Ramps where required complete in all respects as per drawings, specifications and as directed by the Consultant/Engineer.
Specification
9'' (228 mm) Thick or Above Cft
Specification
PLASTER WORK
Specification
Providing and applying Plaster (thickness and cement / sand ratio as indicate in sub items below) including making edges and corners, curing, scaffolding etc, complete in all respects as per drawings, specifications and as directed by the Consultant/Engineer.
Specification
12mm Thick in (1:4) on walls Sft
Specification
P.C.C (1:4:8) UNDER FLOOR
Specification
Providing and laying under floor cement concrete of the nominal mixes by volume as indicated, using 1-1/2'' down guage stone ballast as coarse aggregate, including formwork and its removal, compacting, curing etc, complete in all respects as per drawing, specifications and as directed by the Consultant / Engineer. Cft
Specification
INTERNALPAINT WORKS
Specification
Providing and applying Paint on internal/ External walls of ICI or Berger including rubbing with sand stone, filling the uneven surfaces with putty, rubbing with sand paper and preparation of surface perfect in all respects, applying one coat of primer on prepared surface of plastered and finish paint coats as indicated in sub items, complete in all respects as per drawings.
Specification
Plastic Emulsion Paint ash white (on Internal walls) Sft
Specification
Weather shield paint on external walls (approved by the Engineer) Sft
Specification
Providing and fixing of M.S steel sheet 14SWG on both sides and M.S pipe frame 16SWG frame at inner side of leaf, door frane of M.S angle Iron+M.S dtrip, applying of approved enamel paint and all necessary joinery details, complete in all respect. Sft
Specification

Official source

Always confirm dates, documents, and submission instructions on the originating portal.

View original tender on Federal PPRA / EPADS